Seachem PhosNet 50g Bagged (SC-1250)

Seachem PhosNet 50g Bagged (SC-1250)

PhosNet is a synthetic granular ferric oxide (GFO) that rapidly removes phosphate and silicate from marine and freshwater. It is less dusty than natural GFO, hence easier to use for filtering the aquarium.

Advantages

PhosNet is a granular ferric oxide (GFO) with high porosity, high surface area and high binding capacity. It will rapidly remove phosphates and silicates from both freshwater and saltwater and will not release them back into your aquarium.

It exhibits stronger binding than most competing products and consequently can reduce phosphates and silicates to very low levels. PhosNet also offers less dust and thus is easier to use than most competing GFO products.

Directions

For best results, PhosNet should be rinsed before use and placed so as to maximise the flow of water through it but not so that it tumbles against itself in flow. It may be used in a canister filter, media chamber, box filter, or any high flow area of a trickle filter. Use of a filter bag such as The Bag is recommended.

Use 50 g (1/2 cup) for every 200 L (50 US gallons) saltwater or 400 L (100 US gallons) freshwater. Leave product in place for 4 days, then test phosphate or silicate concentrations with either MultiTest Phosphate or MultiTest Silicate. If the concentration of the component you are trying to decrease has not dropped to around 0.02 mg/L, then replace the PhosNet, otherwise leave in place until levels begin to climb again. As long as concentrations remain under control, the product is not exhausted. Over treating is not recommended. PhosNet is not an exchange resin and does not release anything into the water. It does not leach phosphate or silicate back into the water and may be removed, dried, and returned to service until exhausted. Continuous use of small quantities is better than intermittent use of larger quantities.

FAQ

How do I use PhosNet? How long does it work and when is it exhausted?

A: PhosNet Is best used in smaller quantities and changed frequently. In an environment with an excessively high phosphate reading, PhosNet will exhaust rapidly (4 - 5 days). Place the product in a high flow rate area and test your phosphate levels, changing as needed. When you see that your level is below 0.2 ppm (mg/L) leave that portion of PhosNet in the filter. Continue to test weekly for phosphate until you see it begin to rise again. You will then know that it is time to change the PhosNet. If you have low levels of phosphate the PhosNet will absorb the silicate in your system. It's inert and safe to leave in your filter.

You claim that PhosNet has a high capacity, but Company X claims that their GFO has a capacity that is many times higher. Is this false advertising?

A: It is actually quite easy to change the apparent capacity of a GFO during testing. If the capacity of a GFO is tested at an extremely low pH with a phosphate concentration that is much higher than the media can completely, the media will temporarily absorb much more phosphate than it would under ordinary aquarium conditions. We have no interest in artificially puffing up our numbers, so the capacity we have listed is the amount of phosphate that the media can completely remove (without releasing back into the water) in a pH of 8.4.

Can I use PhosNet in a media reactor?

A: We do not recommend it, as the tumbling action of a media reactor can cause this media to produce dust.

How is this different from PhosGuard, PhosBond, and phosfiltrum (aquavitro)?

A: The main difference between these medias is capacity. PhosGuard has the lowest capacity at 0.82 mg/g of PO4 bound, but is the most economical of the four medias. PhosBond has a higher capacity than PhosGuard at 1.19 mg/g of PO4 bound, and combines the benefits of PhosGuard and a pure GFO (strength, high capacity, and rapid phosphate absorption) while still being very economical. PhosNet has the highest capacity of the Seachem phosphate absorbers at 1.41 mg/g of PO4 bound, and is a pure GFO media. Our aquavitro phosfiltrum is a super-high capacity GFO (1.71 mg/g of PO4 bound) that produces very little dust. This media has a higher capacity than any other GFO on the market.

I was told that products that contain aluminium oxide will release aluminium, which will close corals for weeks and might even damage them. Is this accurate?

A: In recent years, there has been speculation that aluminium oxide based phosphate removers like PhosNet release aluminium into the water and subsequently damage corals. The evidence to support this claim was largely anecdotal.

So, through a series of controlled experiments in both freshwater and saltwater, we intended to address both the question of aluminium solubility and aluminium toxicity. The results of these experiments show that under reef conditions (pH near 8) there is no detectable soluble aluminium released from alumina. Under conditions of low pH and high dosage levels, soluble aluminium can be released from alumina; at three times the label dosage rate, we detected 0.2 mg/L aluminium at a pH of 5.3.

Additionally, aluminium oxide is not easily absorbed into the cell to cause negative reactions. Even at three times the dose, soft-bodied corals such as Sarcophyton remain unaffected.

Company X says that I don't need to replace their phosphate absorber for several months, while your instructions say that PhosNet needs to be replaced every 4 days when reducing phosphate. Doesn't that make PhosNet an inferior product?

A: Not at all! If it takes a phosphate absorber several months to reach its full capacity when the tank has high phosphates, it means that the media is exceptionally slow at absorbing phosphate. PhosNet needs to be replaced every 4 days as long as there is a phosphate problem because, given an infinite amount of available phosphate, PhosNet absorbs phosphate so quickly that it reaches its full capacity in 4 days. The 4 day replacement period is a function of how quickly the media works, not a function of how high a capacity the media has.